Easy Star

Antworten
Razor04
Beiträge: 4
Registriert: 23.08.2008 15:07:11

#1 Easy Star

Beitrag von Razor04 »

Hello all,

sorry for writing in English,bin Englander :D

My question is i want to buy a Easy Star plane,i have already a esky 6 channel Reciever (EK2.0420A) what i took out of my Honeybee King 2 Helicopter.
Can i use this Reciever with my 6 channel Transmitter also with plane?(esky 0406A)



Mfg David Wilkinson
Benutzeravatar
Gerry_
Beiträge: 4161
Registriert: 30.12.2004 23:16:44
Wohnort: Ahnatal

#2 Re: Easy Star

Beitrag von Gerry_ »

Hello David.

You don't have any mixers inside your transmitter, so you can use it for flying Easy Star without problems.
Just take care that the channel reverse settings are correct.

Easy Star is very easy to fly. A well working rework is an increase of the rudder. So you will have less problems to fly while its a little windy.

Best regards ;)

Gerry
Als Trottel dazustehen, wäre heutzutage nicht weiter auffallend.
Denn wer in einem gewissen Alter nicht merkt, daß er von Dummköpfen umgeben ist,
merkt es aus einem gewissen Grund nicht.
( Curt Goetz 17.11.1888 – 12.09.1960 )
Benutzeravatar
tracer
Operator
Operator
Beiträge: 63774
Registriert: 18.08.2004 18:50:03
Wohnort: Kollmar
Kontaktdaten:

#3 Re: Easy Star

Beitrag von tracer »

Welcome David.

Is this your transmitter?

http://www.buzzflyer.co.uk/ESky-0406A-T ... -Guide.asp

It's not a computer transmitter, so it's not capable of being programmed for special use cases.
It's designed to fly a eCCPM helicopter like the belt cp, I see no chance in changig the setup.

The problem is that there are build in mixers for the 120° swash plate.
Benutzeravatar
tracer
Operator
Operator
Beiträge: 63774
Registriert: 18.08.2004 18:50:03
Wohnort: Kollmar
Kontaktdaten:

#4 Re: Easy Star

Beitrag von tracer »

Gerry1973 hat geschrieben:You don't have any mixers inside your transmitter, so you can use it for flying Easy Star without problems.
Does the belt / Honey Bee have an internal mixer in the control unit?

OK, then I was wrong.

Maybe just try it by putting a servo on each needed channel, and check out, what the servo does when moving the appropiate stick.
Benutzeravatar
Memphiz
Beiträge: 91
Registriert: 08.03.2008 19:07:19

#5 Re: Easy Star

Beitrag von Memphiz »

The Mixers in the ESky Transmitter can be disabled by playing with the 2 dipswitches which are located below the batterys. It shouldn't be a problem using this RC-Set for flying an EasyStar.

ciao

Christian
Prôtos 500 FBL (3xDS510, Roxxy 960-6, AR6200, Orig.Motor 15T, BeastX, 9257, SAB Blades)
Align T-Rex 450 SEV2 - Silver (3xHS65HB, Roxxy 940-6, AR6100e, Scorpion HK2221 8 13T, LTG 2100, HS5084MG, Radix Blades)
Funjet
Fox RC
Kyosho Outrage (Ansmann Clash 15, Hitec Regler)
Blade mCX
Spektrum DX6i
Antworten

Zurück zu „EasyStar“